Maximize Uptime
Unplanned breakdowns cost money —sometimes thousands of dollars per hour of downtime. Preventive maintenance catches problems early, before they cause major failures. Less unplanned downtime = more productive hours.
Proper maintenance is the single biggest factor in equipment reliability and service life. A well-maintained unit operates reliably for 15–20+ years; a poorly maintained one may fail prematurely. This maintenance guide covers preventive maintenance schedules, common wear parts, troubleshooting tips, and best practices to keep your equipment running at peak performance.
Preventive maintenance (PM) is proactive —you fix things before they break:
Unplanned breakdowns cost money —sometimes thousands of dollars per hour of downtime. Preventive maintenance catches problems early, before they cause major failures. Less unplanned downtime = more productive hours.
Well-maintained equipment lasts longer. Regular lubrication, timely part replacement, and proper adjustment prevent accelerated wear. A unit that would last 8 years with reactive maintenance can last 15–20+ years with proper PM.
Preventive maintenance costs less than breakdown repair. Replacing a worn seal on schedule costs far less than fixing the damage caused by a catastrophic failure. PM saves money in the long run.
Well-maintained equipment is safer. Regular inspection catches worn components, loose connections, and developing problems before they cause accidents. Safety is non-negotiable.
Effective PM programs use multiple maintenance levels based on operating hours:
| Maintenance Level | Interval (Typical) | Activities |
|---|---|---|
| Daily / Pre-Shift | Every operating day | Visual inspection, fluid level checks, leak check, function test of critical systems |
| Weekly / 50 Hours | ~50 operating hours | Grease all fittings, check belt tension, inspect hoses and fittings, clean filters |
| Monthly / 200 Hours | ~200 operating hours | Change engine oil and filters, inspect hydraulic system, check valve operation, electrical inspection |
| Quarterly / 500 Hours | ~500 operating hours | Detailed inspection of all major systems, wear part assessment, calibration checks, performance test |
| Annual / Overhaul | 1,500–2,000 hours | Major overhaul: pump fluid end rebuild, engine service, full system inspection, worn component replacement |
These are the components that wear out and need regular inspection and replacement:
Pistons, liners, valves, seats, and packing are the main wear parts on reciprocating pumps. Inspect regularly for wear. Keep spares on hand. These are the most frequently replaced pump components.
All seals wear over time. Check for leaks regularly. Replace seals before they fail. Spare seal kits should be in your parts inventory. Common seal materials: NBR, FKM, EPDM, PTFE.
Engine oil filters, fuel filters, air filters, hydraulic filters —all need regular replacement. Dirty filters reduce performance and cause component damage. Follow the filter change schedule in your manual.
Drive belts stretch and crack over time. Hydraulic hoses degrade and can burst. Inspect regularly for cracks, wear, and bulging. Replace before failure. Keep spare belts and hoses on hand.
Quick troubleshooting tips for common equipment issues:
Check: pump prime, fluid level, suction line leaks, valve condition, relief valve setting. Low pressure is often caused by worn pump valves, leaking seals, or air in the system. Start with the simplest check first.
Check: loose mounting bolts, misalignment, worn bearings, cavitation, or internal pump damage. Unusual noise is a warning sign —investigate promptly. Continuing to operate with abnormal noise can cause major damage.
Check: coolant level, radiator cleanliness, belt tension, oil level, ambient temperature. Overheating is often caused by clogged radiators, low coolant, or wrong-grade oil. Address promptly —overheating causes serious engine damage.
Identify the source: loose fitting, damaged seal, cracked component, or worn gasket. Small leaks often grow. Address leaks promptly. Check fluid levels regularly and top up as needed.
Maintenance frequency depends on equipment type and operating conditions. As a general guide: daily visual inspection, weekly greasing and filter checks, monthly oil and filter changes, quarterly detailed inspection, and annual major overhaul. Your equipment's operation manual has specific maintenance schedules based on operating hours. Follow the manual's recommendations.
Keep a recommended spare parts list (RSPL) on hand: common wear parts like pump valves and seats, seals and gaskets, filters (oil, fuel, air, hydraulic), belts, and hoses. For critical equipment, also keep major components like pump fluid end kits. We can provide a recommended spare parts list based on your equipment model and operating conditions.
With proper preventive maintenance, oilfield equipment can last 15–20+ years. Equipment that receives no maintenance or only reactive (breakdown) maintenance may fail prematurely after 5–7 years. The difference is maintenance. A well-maintained unit retains significant resale value even after many years of service.
Yes. We work with customers to develop customized preventive maintenance programs based on their equipment type, operating conditions, and maintenance team capability. We provide maintenance schedules, spare parts lists, and training for your maintenance technicians. Contact us to discuss your maintenance program needs.
Our technical support team is available to help troubleshoot equipment problems. Describe the issue (photos, videos, operating parameters) and we will help diagnose the problem. If remote troubleshooting isn't enough, we can dispatch a service engineer to your location. Don't let a small problem turn into a major failure —ask for help early.
Whether you need a recommended spare parts list, maintenance program design, or technical troubleshooting support, our team is here to help. Keep your equipment running at peak performance.