Shale Gas | Tight Oil | Horizontal Drilling | Multi-Stage Fracturing

Shale Gas Development Equipment

Shale gas and tight oil have transformed the global energy landscape. Development requires a specific set of equipment: horizontal drilling rigs to reach the shale formation, multi-stage hydraulic fracturing to create the fracture network, coiled tubing for well completion and intervention, and production equipment for long-term production. We supply a complete range of equipment for shale gas and tight oil development —from drilling rigs to fracturing spreads to production equipment. Our equipment is proven in major shale plays around the world.

The Shale Development Process

Shale gas development follows a specific sequence:

1. Vertical Drilling

Start with a vertical well drilled down to just above the shale target formation. Uses conventional drilling rigs. The vertical section provides surface access and sets up the horizontal section.

2. Horizontal Drilling

The wellbore turns 90° and runs horizontally through the shale formation for 1,500–2,000+ meters. Maximizes contact with the shale reservoir. Uses advanced directional drilling technology. This is the key to shale development.

3. Multi-Stage Fracturing

The horizontal well is fractured in 20–30+ stages along its length. Each stage creates a fracture network that releases the gas trapped in the shale. Uses large fracturing spreads (10–20 pump units). This is the heart of shale development.

4. Production & Refracturing

The well produces for 20–30+ years. Production declines over time. Refracturing (restimulating the well) can restore production. Uses production equipment and later coiled tubing for refracturing. Long-term production optimization.

Equipment for Shale Development

We supply the full range of shale development equipment:

Stage Equipment Required Key Specs
DrillingLand drilling rigs (1,500–2,000 HP), top drive, MWD/LWDHorizontal capability, 3,000–4,000 m total depth
CementingCementing units, cementing heads, plug shooting toolsHigh-pressure cementing, reliable zonal isolation
FracturingFrac pump units (2,500–3,000 hp), blenders, data vans, sand handlers10,000+ psi treating pressure, 20–30+ stages per well
Coiled TubingCoiled tubing units, plug setting tools, milling toolsWell cleanout, plug deployment, post-frac intervention
ProductionSeparator, compressor, metering, gathering systemLong-term production, dehydration, compression

Major Shale Regions Worldwide

Our shale equipment is suitable for major shale basins:

USA Shale Plays

Marcellus, Permian, Eagle Ford, Bakken, Haynesville, Barnett. The birthplace of shale revolution. Our equipment meets US shale development requirements.

China Shale Gas

Sichuan Basin (Changning, Weiyuan, Fushun). China's major shale gas play. Our equipment is proven in Chinese shale gas operations.

Argentina Vaca Muerta

Vaca Muerta formation —one of the world's largest shale reserves. Major development underway. We supply equipment for Argentine shale projects.

Canada Shale

Horn River, Montney, Duvernay. Canadian shale gas and tight oil. We supply equipment for Canadian shale operations.

Middle East Shale

Saudi Arabia, UAE, Oman —emerging shale gas development. We supply equipment for Middle East shale projects.

Other Shale Regions

Australia, Algeria, Russia, UK. Tell us your shale location, and we will configure accordingly.

Shale Development Challenges

Why shale needs specialized equipment:

High Horsepower Demand

Multi-stage fracturing needs enormous horsepower: 10–20 frac pump units running simultaneously. Total spread HP: 20,000–30,000+. This is much more than conventional oilfield operations.

High Pressure

Shale fracturing typically operates at 8,000–10,000+ psi treating pressure. All equipment must be rated for these high pressures. Safety margins are critical.

Sand Handling

Each frac stage uses 100–200+ tonnes of proppant sand. Total per well: 2,000–10,000+ tonnes. Sand handling, storage, and delivery is a major logistical operation.

Water Demand

Each frac stage uses 1,000–2,000+ cubic meters of water. Total per well: 20,000–100,000+ m³. Water sourcing, treatment, and disposal is a major consideration.

Frequently Asked Questions

What size frac spread do I need for shale development?

A typical shale frac spread includes 10–20 frac pump units (each 2,500–3,000 hp), one blender, one data van, sand handling equipment, and chemical additive units. Total spread horsepower: 20,000–30,000+ HP. The exact size depends on your stage design, treat rate, and formation characteristics. For US-style shale operations, 15–20 units of 5,000 HP is typical. Tell us your design parameters, and we will recommend the right spread size.

What's the difference between shale gas and tight oil?

Shale gas produces natural gas (methane) from shale formations. Tight oil produces light oil from low-permeability rock (tight sandstone or shale). Both use the same development process: horizontal drilling + multi-stage fracturing. The main difference is the produced fluid (gas vs. oil), which affects production equipment. The drilling and fracturing equipment is essentially the same. We supply equipment for both shale gas and tight oil development.

How many stages per horizontal well?

Shale wells typically have 20–30+ frac stages along the horizontal lateral. The number depends on: (1) lateral length (longer = more stages), (2) stage spacing (typically 30–50 m per stage), (3) formation characteristics. Longer laterals (2,000–3,000+ m) with closer stage spacing (30 m) = more stages (50+). This maximizes reservoir contact. Tell us your lateral length and stage spacing, and we will help design the fracturing operation.

Do you have experience with Chinese shale gas operations?

Yes. We have supplied fracturing and related equipment for Chinese shale gas operations (Sichuan Basin). We understand the specific requirements of Chinese shale development: challenging mountain terrain, high-pressure formations, and specific operator requirements. Tell us your project location and operator, and we will discuss our relevant experience.

What is refracturing (restimulation)?

Refracturing is restimulating an existing shale well that has declined in production. New fractures are created (or existing ones re-opened) to restore production. Uses similar equipment to initial fracturing. Typically done 3–5 years after initial completion. Can restore 50–70% of initial production. Refracturing is increasingly common as shale wells age. We supply equipment for refracturing operations.

Planning a Shale Development Project?

Tell us about your shale project: formation, lateral length, stage design, and equipment needs. Our engineering team will design the right equipment package for your shale development.