Mobile Frac Manifold | Fast Move | Zipper Frac

Manifold Truck: Drive Up, Hook Up, Start Pumping

In shale fracturing, time is money. A multi-well pad might have 8-12 wells, each needing 20-40 frac stages. Moving the frac spread from one well to the next should take hours, not days. A manifold truck solves this: the entire frac manifold —all the valves, piping and connections —is mounted on a heavy-duty truck chassis. You drive it up to the well, connect the pump lines and the wellhead line, and you're ready to pump. When the well is done, you disconnect and drive to the next well on the pad. No crew spending days bolting together a skid-mounted manifold on location. This is how modern shale frac crews do it.

Mobile frac manifold truck on location

Manifold Truck vs Skid-Mounted Manifold

Both do the same job, but for different operating styles:

Manifold Truck Skid-Mounted Manifold
Rig-up time 1 - 2 hours (drive up, connect) 1 - 2 days (assemble on location)
Move time between wells 30 minutes (disconnect and drive) Half a day to a day (disassemble and reassemble)
Best for Multi-well pads, zipper frac, continuous operation Single-well operations, remote locations
Crew size needed 1 - 2 operators 4 - 6 rig-up crew
Initial cost Higher (truck chassis + manifold) Lower (just the skid)
Annual operating cost Lower (less labor, less downtime) Higher (more rig-up time, more crew hours)

What's Mounted on the Manifold Truck

Full Frac Manifold

The complete frac manifold: header lines, branch lines, gate valves, flanges and connections. All pre-assembled and tested at the factory. Ready to use as soon as you drive up.

Hydraulic Valve Actuation

All valves are hydraulically actuated —the operator opens and closes them from a control panel on the truck, or remotely from the control van. No manual valve turning on location.

Pressure Monitoring System

Pressure transmitters at every critical point, with real-time readout on the truck's control panel. The operator sees exactly what pressure is on each branch, right from the truck.

Heavy Duty Truck Chassis

Built on a heavy-duty tri-axle or quad-axle truck chassis capable of carrying the weight of the manifold and all the piping. Rated for on-highway transport between well sites.

Typical Manifold Truck Specifications

Parameter 10K Manifold Truck 15K Manifold Truck
Pressure rating 10,000 psi (70 MPa) 15,000 psi (105 MPa)
Pump connections 4 - 6 outlets 6 - 8 outlets
Wellhead connections 1 - 2 outlets 1 - 2 outlets
Valve type API 6A gate valves, hydraulic actuated API 6A gate valves, hydraulic actuated
Chassis Tri-axle heavy duty truck Quad-axle heavy duty truck
Operating weight ~25 tonnes ~35 tonnes

Frequently Asked Questions

How long does it take to rig up a manifold truck on location?

Typically 1-2 hours: drive the truck into position, connect 4-6 pump hoses from the frac pumps to the truck's inlets, connect the high-pressure line to the wellhead outlet, and do a pressure test. Compare that to a skid-mounted manifold that takes a full day or more to assemble on location. The manifold truck saves you hours of rig-up time on every well. On a multi-well pad with 10 wells, that's a full day saved just on rig-up/down.

Can I drive a manifold truck on public roads?

Yes. The manifold truck is built on a certified truck chassis that's registered for on-highway use. You can drive it between well sites on public roads, just like any other oilfield truck. No special hauling permits needed for normal inter-well moves on a pad. If you're moving between fields hundreds of kilometers apart, it's the same as any heavy truck —check local weight and permit requirements.

What's a "zipper frac" and how does the manifold truck help?

A zipper frac is where two wells on the same pad are frac'd in an alternating sequence: stage 1 on well A, stage 1 on well B, stage 2 on well A, and so on. The manifold truck makes this efficient: after finishing well A, you just drive the truck over to well B (30 minutes) and keep pumping. No downtime while crews disassemble and reassemble the manifold. The frac pumps stay running, the crew stays working, and you get through the pad faster. This is the standard operating procedure on modern shale pads.

Need a Manifold Truck for Your Frac Operation?

Tell us your required pressure rating (10K or 15K), number of pump connections, and truck chassis preference. We'll configure a manifold truck that matches your frac fleet and operating style.