Drilling-Equipment

3000m Super Single Drilling Rig

3000m Super Single Drilling Rig is a field-deployable drilling rig package for hoisting and rotary drilling. The shortlist starts with depth target and mast handling and the control package.

3000m Super Single Drilling Rig (ZJ30), 1700kN hook load, AC VFD onshore rig for oil and gas drilling
Product description

ZJ30 3000m Super Single Drilling Rig

The ZJ30 3000m Super Single is an AC VFD land drilling rig rated for 3000 m nominal drilling depth with 114 mm drill pipe. With a 1700 kN (382,000 lb) hook load and a single F-1600 mud pump, it is designed for shallow to medium-depth oil and gas exploration and development wells where rig mobility and small footprint matter more than ultra-deep capability.

The defining feature of this rig is its super single mast design: the top drive (225 t capacity) is integrated inside the K-type mast during transport, and the entire rig splits into only three truck loads. This eliminates the need for oversize transport permits and cuts rig-up time on location compared with conventional ZJ30-class rigs that require five or six loads. The compact substructure also suits small well sites in hilly, farmland or desert-edge terrain where pad space is limited.

Technical Highlights

What distinguishes this rig

Drive System

AC VFD electric drawworks

Two 400 kW (536 hp) AC motors with variable-frequency drive replace the mechanical chain-and-clutch drawworks of older ZJ30 rigs. Hoisting speed is stepless, giving smoother trips and lower wear on brake blocks. The VFD package also regenerates energy during lowering, reducing fuel consumption versus a mechanical drive.

Mast Design

Super single K-type mast

The mast is a single-section K-type structure raised by hydraulic cylinders in one lift. The 225 t top drive rides inside the mast during transport and is lowered to working position on site —no separate top-drive truck and no pinning assembly required.

Mud Pump

1 × F-1600 triplex pump

One F-1600 triplex single-acting piston pump (1600 hp, 52 MPa discharge) handles circulating for 3000 m holes. A second pump skid can be added as an option if the program calls for heavy-weight mud or high-rate aerated drilling.

Mobilization

Three-load transport

Load 1: drawworks and rotary table module. Load 2: mast + substructure. Load 3: mud pump and solids control package. All three loads fit standard heavy-haul trucks without wide-load escort, which is the main reason field crews pick this rig over a conventional ZJ30 on short-location campaigns.

Substructure

Box substructure for small pads

The drill-floor substructure is a box-type design with a low installation height. It is selected where the well site is constrained —hilly terrain, farmland reclamation, or desert-edge pads where cutting a larger location would cost more than the rig itself.

Control

Stand-alone driller cabin

An air-conditioned driller's cabin with VFD HMI, mud logging readout and brake control is mounted on the drill floor. The cabin is ISO-compliant for noise and vibration, and can be heated for winterized packages.

Applications

Where this rig fits

  • Shallow to medium-depth wells: 2000–3000 m oil and gas exploration and development wells with 114 mm drill pipe.
  • Small well sites: hilly, farmland, desert-edge or urban-fringe locations where pad area is limited.
  • Cluster / pad drilling: short-relocation campaigns where the three-load transport saves mobilization cost versus a heavier ZJ50.
  • Winterized service: optional -40°C package for Central Asian or northern Chinese oilfields.
Selection Guide

Is the 3000 m Super Single rig the right fit for your drilling program?

This rig is a modern AC VFD electric rig built around a single-section K-type mast and 225 t top drive. It replaces older ZJ30 mechanical rigs in the 3,000 m class. The "super single" designation means the mast is raised in one lift and the top drive rides inside the mast during transport — reducing rig-up time from days to hours compared with multi-section masts.

Choose this rig when:

  • Target depth is 2,000–3,200 m. The 225 t hook load rating covers intermediate and production casing running in this depth range. Below 2,000 m you can use a smaller ZJ20 rig; above 3,200 m you step up to the ZJ40/ZJ50 class.
  • Rig-up / rig-down time matters. The one-lift mast design and truck-mountable substructure let a two-person crew rig up in 8–12 hours. If your program moves rigs every 2–4 weeks (development drilling, infill drilling), the time saved on each move pays back the rig premium quickly.
  • You want electric VFD controls, not mechanical. The AC VFD drawworks gives stepless speed control, regenerative braking, and lower fuel consumption than a mechanical chain drive. This matters if you are running 24/7 and fuel cost is a major line item.
  • Mud pump requirement: single F-1600 is enough. One F-1600 (1600 hp, 52 MPa) handles circulation for 3,000 m holes with standard mud weights. If you are drilling high-pressure gas wells or need heavy mud, add the second pump skid option.

3000 m Super Single vs older ZJ30 mechanical rig — why upgrade?

  • Old ZJ30 mechanical: Cheaper upfront, but slower trips, higher brake wear, higher fuel consumption, and longer rig-up time. Best for low-frequency drilling where moves are rare.
  • Super Single VFD (this rig): Higher upfront cost, but faster trips, lower fuel use, faster rig-up, and better safety. Pays back the difference in 1–2 years on an active drilling program.
How It Works

Drilling system overview

The rig is organized into four systems. The hoisting system (AC VFD drawworks, wire line, traveling block, 225 t top drive) handles pipe trips. The rotating system uses the top drive for most drilling, with a 756 mm (29-1/2") rotary table for casing and fishing. The circulating system is the F-1600 triplex pump feeding a standard solids-control chain (shale shakers, desander, desilter, degasser). The power system is a cluster of diesel generators feeding the VFD bus.

Mobilization sequence: pull the rig, lay the mast down hydraulically, split into three loads, truck to the next location, raise the mast in one lift, and rig up the circulating line. Typical rig-up time after arrival is 1–3 days for an experienced crew.

Configuration Options

Common selections

  • Winterized package: engine heaters, heated cabin, anti-freeze hydraulic fluid for -30°C to -45°C service.
  • Desert package: sand-fill radiators, pre-cleaners, dust-sealed electrical cabinets.
  • Second mud pump: add a second F-1600 skid for deep or heavy-mud programs.
  • IPO / iron roughneck: optional pipe-handling automation on the drill floor.
  • Mast height: standard 31.5 m; taller mast available for longer stands.
FAQ

Buyer questions

Q: What drill pipe size does the 3000 m rating use?
A: The 3000 m nominal depth is rated on 114 mm (4-1/2") drill pipe. With 127 mm pipe the rated depth drops to roughly 2200 m.:

Q: What are the three transport loads exactly?
A: Load 1: drawworks + rotary + engine room skid. Load 2: mast + substructure. Load 3: mud pump + solids control. All three are standard heavy-haul loads without escort in most jurisdictions.

Q: Can this rig operate in cold weather?
A: The base rig is rated for -20°C. The winterized package extends this to -40°C or -45°C with engine pre-heaters, heated cabin and arctic-grade hydraulic fluid.

Q: What is the typical delivery lead time?
A: Six to eight months from order to shipment for a new rig, depending on option list. Refurbished or stock units can ship in 60–90 days.

Q: Do you supply this rig on an OEM basis?
A: Yes. SJ Petroleum Machinery supplies both under our own brand and under customer brand names for drilling contractors and oilfield service companies.

Why SJ Petro

Manufacturing background

SJ Petroleum Machinery is a factory-direct manufacturer of oilfield equipment. We have built drilling rigs since 1941. The ZJ30 super single platform is API 4F certified, and rigs of this class have shipped to operators in the Middle East, Central Asia, Africa and Southeast Asia. Each rig is factory-tested under load before shipment, and we supply commissioning, operator training and spare parts on site.

Get a Quote

Ready to discuss this model?

Send your target drilling depth, mud weight, well-site terrain and preferred power configuration. We will return a tailored rig layout and pricing within 48 hours.

Product Parameters

Parameter table

ModelNominal drilling depth m (drill pipe)Max. hook load kN(lb)Drawworks rated power kW(hp)Rotary table opening mm(in)Top drive capacity tMud pump configurationMobilization
3000m Super Single (ZJ30)3000 (drill pipe 114mm)1700(382,000)2×400(2×536), AC VFD756(29-1/2")2251×F-1600 (1600 hp)3 truck loads, top drive integral in mast
Related products

More from Drilling-Equipment

8000m Swing-Up Drilling Rig
8000m-Swing-up-drilling-rig

8000m-Swing-up-drilling-rig

8000m Swing Up Drilling Rig is a field-deployable drilling rig package for hoisting and rotary drilling. The shortlist starts with depth target and mast handling and the control package.

View details
BE770 Big Easy Drilling Rig
BE770-Drilling-Rig

BE770-Drilling-Rig

Be770 Drilling Rig combines drilling rig package duties with a field-deployable layout. Buyers usually check working capacity and power arrangement, field-side control, and field operation.

View details
Cluster Well Drilling Rig Transport Device Between Wells
Cluster-well-drilling-rig-transport-device-between-wells

Cluster-well-drilling-rig-transport-device-between-wells

Cluster Well Drilling Rig Transport Device Between Wells combines drilling rig package duties with a field-deployable layout. Buyers usually check site footprint, field-side control, and cluster-well logistics.

View details
Cold Weather Drilling Rig for Low-Temperature Operations
Cold-weather-drilling-rig

Cold-weather-drilling-rig

Cold Weather Drilling Rig suits buyers who need hoisting and rotary drilling in a field-deployable format. Its fit depends on depth target and mast handling and the project duty cycle.

View details
Cold Weather Wheel-Rail Drilling Rig
Cold-weather-wheel-rail-drilling-rig

Cold-weather-wheel-rail-drilling-rig

Cold Weather Wheel Rail Drilling Rig suits buyers who need hoisting and rotary drilling in a field-deployable format. Its fit depends on depth target and mast handling and the project duty cycle.

View details
Desert Fast-Moving Drilling Rig
Desert-fast-moving-drilling-rig

Desert-fast-moving-drilling-rig

Desert Fast Moving Drilling Rig combines drilling rig package duties with a field-deployable layout. Buyers usually check depth target and mast handling, field-side control, and desert conditions.

View details