Drilling-Equipment

Top Pressure Drilling Rig

Top Pressure Drilling Rig combines pressure-controlled drilling package duties with a field-deployable layout. Buyers usually check depth target and mast handling, field-side control, and field operation.

Top-Drive Drilling Rig (ZJ50), 3150kN hook load, integrated top drive
Product description

ZJ50 Top-Drive Drilling Rig, 3150 kN

The ZJ50 is an AC VFD land drilling rig rated for 3150 kN hook load and 5000 m nominal drilling depth with 114 mm drill pipe. What distinguishes this rig is the integrated top-drive package: the top drive is not an add-on but is designed into the mast, wire-rope system and control panel from the start.

Most ZJ50-class rigs offer top drive as an option that crews add later. On this rig, the top drive is sized to match the hook load, the VFD is programmed for top-drive operations, and the driller's cabin includes a top-drive HMI as standard. This makes the rig faster on trips and more efficient on directional wells.

Technical Highlights

Integrated top drive

Top Drive

350 t top drive, integrated

A 350 t top drive (electric, AC VFD) is standard. It provides continuous rotation while tripping, which cuts connection time and reduces stuck-pipe risk on directional wells.

Hook Load

3150 kN for 5000 m wells

Rated hook load 3150 kN (708,000 lb), with a 250 t traveling block. Designed for 5000 m onshore oil and gas wells, including directional and horizontal wells.

VFD Control

Top-drive-aware VFD programming

The VFD is programmed for top-drive operation: soft-start rotation, torque limiting, and integrated stick control. The driller can make connections without stopping the drawworks.

Mud Pumps

Two F-1600 pumps

Two F-1600 triplex pumps (1600 hp each) provide redundant circulation for 5000 m holes with heavy mud.

Rotary Table

1257 mm rotary for casing

A 1257 mm (49-1/4") rotary table is retained for casing running and fishing, even though the top drive handles most drilling.

Directional Capability

Ready for MWD/LWD

The mast and floor are prepared for MWD/LWD tools, with a dedicated wire-line route and a top-drive kelly bushing for directional drilling.

Applications

Where this rig fits

  • Directional and horizontal wells: where top-drive efficiency matters.
  • 5000 m development wells: onshore oil and gas in mature basins.
  • High-angle wells: where stuck-pipe risk makes continuous rotation valuable.
Selection Guide

Is this ZJ50 top-drive rig the right fit for a 5,000 m well program?

This is a ZJ50-class rig (3,150 kN hook load) with an integrated 350 t AC VFD top drive. The top drive is not an add-on here — it is designed into the VFD control system from the start, with soft-start rotation, torque limiting, and the ability to make connections without stopping the drawworks. This matters most on directional and horizontal wells.

Choose this rig when:

  • Target depth is 4,000–5,000 m. 3,150 kN hook load is the sweet spot for 5,000 m onshore wells. Below 4,000 m, a ZJ40 rig is more economical; above 5,000 m you step up to ZJ70.
  • You drill directional or horizontal wells. Top drive is the standard tool for directional drilling: you can rotate the string while tripping, which cuts connection time and reduces stuck-pipe risk. If your program is 100% vertical development wells, a rotary-table rig costs less.
  • You need redundant circulation. Two F-1600 pumps (1,600 hp each) mean if one pump fails mid-hole, the other keeps circulation going. This matters in deep or high-risk intervals where lost circulation would be expensive.
  • You want VFD efficiency over mechanical drive. The AC VFD package gives stepless speed, regenerative braking, and lower fuel consumption. On a 24/7 drilling program, this typically cuts fuel cost 15–20% versus mechanical drive.

ZJ50 top drive vs ZJ50 rotary table — what does the top drive actually change?

  • Rotary-table ZJ50: Lower upfront cost, simpler controls. Best for vertical wells with few directional sections, where connection time is a minor factor.
  • Top-drive ZJ50 (this rig): Higher cost, but faster connections on directional wells, less stuck-pipe risk, and better for horizontal drilling. Pays back the premium on the first long directional well.
FAQ

Buyer questions

Q: Is top drive available as an option on other rigs?
A: Yes, but on ZJ30/ZJ40 class rigs it is often retrofitted. On this ZJ50, top drive is integrated from the factory, which means better wire-rope routing and VFD tuning.

Q: How much faster is top drive than kelly drilling?
A: Typically 20–30% faster on connections, and significantly faster on directional wells where reaming is needed.

Q: Can it handle 6000 m wells?
A: The rig is rated for 5000 m. With 89 mm pipe, it can reach 6000 m, but hook load margin is reduced.

Q: What is the typical price range for this equipment?
A: Pricing depends on capacity, configuration, and option list. Contact our sales team with your requirements for a detailed quote. We offer factory-direct pricing with no middleman markup.

Q: Do you provide on-site commissioning and operator training?
A: Yes. We provide on-site installation supervision, commissioning, and operator training as part of every package. Our service engineers travel worldwide to support your team during startup and operation.

Get a Quote

Ready to discuss this rig?

Send your target depth, well profile (vertical/directional/horizontal), and whether you run MWD. We will return a layout and pricing within 48 hours.

Product Parameters

Parameter table

ModelNominal drilling depth m (drill pipe)Max. hook load kN(lb)Top drive capacity tTop drive power kWDrawworks power kW(hp)Mud pumpDrive
ZJ50 Top-Drive5000 (drill pipe 114mm)3150(708,000)4502×350 (AC)2×800(2×1070), AC VFD2×F-1300 (1300 hp each)Fully AC VFD, top-drive integrated in mast
Related products

More from Drilling-Equipment

3000m Super Single Drilling Rig
3000m-Super-single-drilling-rig

3000m-Super-single-drilling-rig

3000m Super Single Drilling Rig is a field-deployable drilling rig package for hoisting and rotary drilling. The shortlist starts with depth target and mast handling and the control package.

View details
8000m Swing Up Drilling Rig
8000m-Swing-up-drilling-rig

8000m-Swing-up-drilling-rig

8000m Swing Up Drilling Rig is a field-deployable drilling rig package for hoisting and rotary drilling. The shortlist starts with depth target and mast handling and the control package.

View details
BE770 Drilling Rig
BE770-Drilling-Rig

BE770-Drilling-Rig

Be770 Drilling Rig combines drilling rig package duties with a field-deployable layout. Buyers usually check working capacity and power arrangement, field-side control, and field operation.

View details
Cluster Well Drilling Rig Transport Device Between Wells
Cluster-well-drilling-rig-transport-device-between-wells

Cluster-well-drilling-rig-transport-device-between-wells

Cluster Well Drilling Rig Transport Device Between Wells combines drilling rig package duties with a field-deployable layout. Buyers usually check site footprint, field-side control, and cluster-well logistics.

View details
Cold Weather Drilling Rig
Cold-weather-drilling-rig

Cold-weather-drilling-rig

Cold Weather Drilling Rig suits buyers who need hoisting and rotary drilling in a field-deployable format. Its fit depends on depth target and mast handling and the project duty cycle.

View details
Cold Weather Wheel Rail Drilling Rig
Cold-weather-wheel-rail-drilling-rig

Cold-weather-wheel-rail-drilling-rig

Cold Weather Wheel Rail Drilling Rig suits buyers who need hoisting and rotary drilling in a field-deployable format. Its fit depends on depth target and mast handling and the project duty cycle.

View details