ZJ80DB Synchronous-Lifting Drilling Rig, 5850 kN
The ZJ80DB is an AC VFD land rig rated for 5850 kN hook load and 8000 m depth. The "synchronous-lifting" designation refers to the substructure raising system: instead of hydraulic cylinders, the drill floor is raised by synchronized chain drives —one chain on each corner, driven by a common hydraulic power unit that keeps all four chains in sync.
Chain-driven lifting is preferred over hydraulic cylinder lifting on heavier rigs because it offers longer stroke (the drill floor rises from 3 m to 9 m in one continuous motion), better load distribution, and less maintenance than large-bore hydraulic cylinders. This is the standard substructure design on ZJ80 and ZJ90 class rigs.
Chain-driven synchronous lift
Four-corner synchronized chains
Heavy-duty roller chains on each corner of the substructure raise the drill floor. A common hydraulic power unit drives all four chain motors, with electronic synchronization that keeps each corner within 5 mm of the others.
3 m to 9 m in one lift
The drill floor rises from 3 m transport height to 9 m working height in a single chain lift. No intermediate pinning, no second-stage cylinder.
5850 kN for 8000 m wells
Rated hook load 5850 kN (1,315,000 lb), with a 400 t traveling block. Designed for 8000 m deep drilling.
Chain vs cylinder comparison
Chains are simpler to maintain than large-bore hydraulic cylinders: no seal replacements, no cylinder rod polishing, just periodic chain lubrication and tension check. This matters for remote locations.
9 m cellar clearance
The 9 m working height accommodates a 13-5/8" 105MPa BOP stack plus a riser, which is the standard for HPHT deep wells.
4 hours to working height
The chain-driven substructure reaches 9 m working height in about 4 hours, including synchronization check and pinning.
Chain-synchronous lift or hydraulic cylinder lift — which substructure for your ZJ80?
The ZJ80DB is an 8,000 m-class rig (5,850 kN hook load) that raises its drill floor with four-corner synchronized chains instead of large hydraulic cylinders. The lift goes from 3 m transport height to 9 m working height in one continuous stroke — no intermediate pinning, no second-stage cylinder. It shares the same 5,850 kN hook load as the ZJ80D, so the choice between them is mostly about the substructure lift mechanism and what your maintenance crew is trained on.
Choose the chain-lift ZJ80DB when:
- Your maintenance team is mechanical, not hydraulic-specialist. Chains need periodic lubrication and tension checks — no seal replacement, no cylinder rod polishing, no hydraulic leak hunting. If your field has strong mechanics but limited hydraulic technicians, the chain system is easier to keep running.
- You need a single continuous lift to 9 m. The one-stroke chain lift (3 m → 9 m) eliminates the intermediate pinning and the risk of a second-stage cylinder failing. If your wellhead/BOP setup requires 9 m clearance (large BOP stacks, mudline systems), this gives you that height without two-stage complexity.
- Rig-up time is part of your cost model. The synchronized chain lift raises the floor in one controlled motion with electronic synchronization (each corner within 5 mm). This is repeatable and fast — crews learn it once and rig-up in hours, not days.
- You are comparing against a cylinder-lift ZJ80. Both rigs drill the same 8,000 m wells with the same hook load. The decision is maintenance philosophy: chains (simpler, mechanical) vs cylinders (more compact, hydraulic expertise required).
Chain-lift ZJ80DB vs cylinder-lift ZJ80D — which is right for you?
- Choose the cylinder-lift ZJ80D: Your crew already maintains hydraulic cylinders, you want the most compact package, and you value cylinder smoothness on every lift.
- Choose the chain-lift ZJ80DB (this rig): Your maintenance strength is mechanical, you want 9 m clearance in one stroke, and you prefer simpler long-term maintenance with fewer specialized seals and rods to stock.
Buyer questions
Q: How is this different from ZJ80D?
A: Same hook load (5850 kN) and depth (8000 m), but the substructure uses chain-driven synchronous lifting instead of hydraulic cylinder lifting. The ZJ80D also includes the full automation package; this ZJ80DB is a more conventional rig with the chain-lift substructure.
Q: Which is better, chain or hydraulic cylinder?
A: Chain drive for longer stroke and less maintenance; hydraulic cylinder for simpler control. For 8000 m class rigs with 9 m cellar clearance, chain drive is the industry standard.
Q: What is the typical price range for this equipment?
A: Pricing depends on capacity, configuration, and option list. Contact our sales team with your requirements for a detailed quote. We offer factory-direct pricing with no middleman markup.
Q: Do you provide on-site commissioning and operator training?
A: Yes. We provide on-site installation supervision, commissioning, and operator training as part of every package. Our service engineers travel worldwide to support your team during startup and operation.
Q: What is the typical delivery lead time?
A: 6–8 months for new equipment, depending on configuration. Refurbished or stock units can ship in 60–90 days. Contact us for your specific model lead time.
Ready to discuss this rig?
Send your target depth and required cellar height. We will return a layout and pricing within 48 hours.